MX9 MX9V Track section Module with full functionality
Manual MX9 can be used in different ways . . . ... for slow driving sections, automated station entries etc.: These represent the simple cases, where no programming is needed. ... for system autonomous operation (without a Computer):
An MX1 command station is in control of, e.g. automatic block operation. Blocks are divided into sections (Fully explained in the operating manual), which in turn are connected to one or several MX9 modules. To define an automatic block operation the necessary information is entered on the MX2 cab while driving an engine on the corresponding sections of track. ... Computer control:
With the help of the "STP" software (E.Sperrer software development) all events can be supervised and controlled, on screen, from a computer generated layout map. All prototypical functions for safe and secure train movements can be implemented.
The MX9 products are responsible for the trains safety, that is, besides occupancy detection, especially for the unique ZIMO "signal controlled speed limits", "local function control" and engine number recognition.
Occupancy detection of 16 track sections with MX9V or MX9B module: Current consuming vehicles will be recognised on a track section Current consumption of an idle decoder or cars with a small resistor across axle is sufficient Local display of occupied track sections by means of 16 LED's at the module External display through connected bulbs or at the computer.
"Signal controlled speed limits":
- Stopping of trains before a red signal (in "stop sections")
- without loosing control over lights and functions,
- Signal dependent speed limits in 5 steps for decelerating trains or for slow speed sections
- Full control of all functions even while train is stopped or limited in speed in a slow speed section
- With the help of the MAN button, all above mentioned limits can be lifted, individually for every selected engine.
"Local function control":
- Automatic "on" of selected functions of a ZIMO function decoder in specified sections of track
- "and", "or", "not and" combinations, with individual control.
Loco number recognition:
- Evaluation of acknowledgment pulse from ZIMO decoder
- Train number displayed on display module or computer. ("STP" software ) Track voltage (from command station) 12 V to 24 V Occupancy detection threshold (depends on track voltage) 13 K Ohm (12 V) to25 K Ohm (24 V) Maximum single output current (power turn-off depend. voltage) 2,8 A (to12 V) to 4,4 A (at 24 V) Total current of all outputs 8 A Dimensions 172 x 112 x 40 mm MX9V Full version, covering 16 track sections grouped to 8 blocks. An occupancy detection is performed on each of the 16 sections and the "signal controlled speed limits" as well as the "local function control" can be applied to each block (made up of two sections). Engine number recognition and location for ZIMO decoders is performed on every block (on which a plug-in board MX9AZN is installed).
MX9 modules will be shipped without a CAN bus cable, because the cable length needed can vary greatly. Don't forget to order a CAN bus cable in the desired length together with a track section module or the material necessary to make one yourself (including a divider box, if needed)! Plug-in boards (sockets are provided inside the MX9): MX9AZN For Loco number recognition on one of 8 blocks of a MX9 (each block is made up of two adjacent track sections, from a total of 16). Altogether there are 8 sockets (one for each block) ready to be furnished with MX9AZN boards. Recognition and storage of up to 4 engine numbers per block simultaneously, then sent to a computer or to a remote MX9ZIA display module (connected to MX9). MX9ALA For remote occupancy indication (e.g. switch board) and block signals. Each MX9ALA board (4 slots in each MX9) controls 8 bulbs for 8 occupancy indicators or 4 signals with red/green indication. In "STP", each of those output pins can be freely assigned, that is, independent of the module's block assignment. An affordable alternative to operate signals. MX9ASE For the direct use of the "signal controlled speed limit", triggered by external switches, relays etc. (that is, without the use of system autonomous control or computer). 8 inputs for each MX9ASE board (room for two boards in each MX9). External display module: MX9ZIAP 8 digit LED display module (red digits), connected to a MX9. Separate power supply socket (12 - 15 V transformer needed). For each block, a LED display module can be installed provided a MX9AZN board is plugged in for that block. Simultaneous display of 3 two digit or 2 three digit engine addresses possible; alternate display when more than 2 resp. 3 engine addresses are present per track section . MX9ZIAW As MX9ZIAP, but in an angled frame, which is more suitable to be installed in a switch board
|