LENCO 3866 USB TURNTABLE
# Midi turntable (420 mm width)
# USB connection
# Semi automatic
# Belt drive
# Auto Return
# Auto shut off
# 2 rated speed 33 1/3 rpm and 45 rpm
# Moving magnetic cartridge
# Incl. needle
# Incl. pre amplifier
Powersource : AC 230V/50 Hz
- Dimensions : 420 x 330 x 94 mm
- Weight : 2.400 g.
CONTENTS-----------------------------2 DESCRIPTION-------------------------3,4 INITIAL STARTING-UP------------------5 Main Connection Amplifier Connection-------------------5 Playing a record-----------------------5 MAINTENANCE ------------------------6 To replace the stylus------------------6 To disassemble the cartridge-----------6 To install new pick-up head-------------6 Important recommendations-------------6 Audacity Software Instruction----------7-20 1. Adapter: Use this adapter when playing 45 RPM records. 2. Platter: Platter change in the record will be placed here 3. Tonearm set 4. Tonearm Lock: Use this lock to keep the tonearm in place when not in use. 5. Dust Cover: Use this to protect the turntable from exposure to dust. The cover may be opened or removed during use, but should remain closed when the turntable is not in use. 6. USB port: - With Full-Speed Transceivers - Fully Compliant With USB 1.1 Specification Connect to PC for editing the music with your favorite digital editing software, if you need the information of free editing software; please check the website http://audacity.sourceforge.net/ , and check the attached software instruction. 7. Signal Connectors: Use these to connect the turntable to the mixer or amplifier in your sound system. 8. Power Cord: Connect this cord to a grounded AC outlet of the proper voltage. 9. Arm Lift Button 10. Stop Button 11. Speed Button: Button locked 45rpm Button unlocked 33 rpm I NITIAL STARTING-UP MAINS CONNECTION Ensure that the mains voltage of your home corresponds to the operating voltage of the unit. Your unit is ready to be connected to a mains voltage of 110V/60Hz or 220V/50Hz. AMPLIFIER CONNECTION Connect audio plugs to Alert input on your mixer or amplifier: Red plug into R/H channel input. White plug into L/H channel input. Playing a record - Remove the Dust cover from the turntable. - Place the record of your choice on the turntable. If it is a 45 rpm, do not forget to place the adaptor on the record spindle. - Choose the desired playing speed: 33 rpm -> button unlocked 45 rpm-> button locked. - Release the Tone-arm lock. - Push in the arm lift button (tone-arm will go up) - Place the cartridge vertically over the first track of the record the turntable starts turning - Push out the arm lift button (tone-arm will lower record starts playing) - When the record is over, the tone-arm returns to its rest and the turntable starts turning. Remark: While the record is ON, If you wish to: Stop the record while its playing Press the stop button; the cartridge comes up and returns to it s rest; the turntable stops turning. Replace the protective cap on the stylus Close the tone-arm lock. M AINTENANCE TO REPLACE THE STYLUS (FIG.A) - Put the rest clip on the pick-up arm. - Pull the stylus in the direction of arrow (A) and remove it. - Put in the new stylus following the reverse procedure. TO DISASSEMBLE THE CARTRIDGE (FIG.B) - Put the rest clip into the pick-up arm. - Remove the stylus (see section above). - Release the pick-up head by pushing the cartridge in the direction of arrow. - Disconnect the three cables link wires at the level of the pick-up head. TO INSTALL NEW CARTRIDGE - Connect the three link wires as shown in figure. - Push the cartridge into headshell - Re-position the stylus IMPORTANT RECOMMENDATIONS We advise you to clean your records using a rag impregnate with an antistatic product for maximum enjoyment of your records and also to make them last. We would also point out that for the same reason your stylus should be replaced periodically (approximately every 250 hours) Dust the stylus from time to time using a very soft brush dipped in alcohol (brushing from back to front of the cartridge) WHEN TRANSPORTING YOUR RECORD PLAYER DO NOT FORGET TO: Replace the protective cap on the stylus. Put the rest clip into the pick-up arm. REST OF THE MANUAL HERE
|