Elite CSW-200-UL High Traffic Commercial Swing Gate Operator FEATURES AND SPECIFICATIONS MODULAR BOARD: Uses LEDs to indicate all input and output functions of the gate operator. ERD SENSOR: If the gate hits a vehicle while closing, it reopens. If it hits a vehicle while opening, it stops, reverves 4 to 6 inches, and stops again. DIGITAL MOTOR PROTECTIONS: Entrapment sensor shuts off the motor after it reaches the stall amp for 3 seconds, reverves direction for several inches, a nd stops. ELECTRONIC INPUTS: Radio receiver, key switch, safety loop, center loop, telephone entry system, computer input, fire dept. key switch and 3 push-button stations. TIMER: Adjustable timer can be set from 0 to 60 seconds. POWER INPUT ON/OFF SWITCH: Controls power input to the board with convenient switch. MAGNETIC LOCK: With Omni Option board, magnetic lock system is incorporated, allowing you to easily add the "MG1300" electromagnetic locking system to the gate. INTELLIGENT PRIMARY/SECONDARY: Precise, synchronized movement and communication between two gate operators using three wire res-485 bi-directional technology. GATE TRAVELING TIME: Adjusted by a precision mechanical device an electrical limit switch system. SOFT STOP: Gate travels through the cycle at normal speed and comes to a stop slowly for a more accurate gate cycle. INTERGATED LOOP DETECTORS: Easy to install, modular, plug in loop detector inputs for exit loop, center loop, and safety loop. MOTOR DRIVE: Solid state electronic motor drive system is incorporated into board. BUGLAR ALARM: With OMNI Option board, interfaces with exsisting home alarm or alarm output. 3 PUSH BUTTON CONTROL: On board gate operator control for close, stop, and open. ELECTRICAL SPECIFICATIONS
- 120 VAC Power Built-in 120 VAC power receptacle (NEMA 5-15)
- Alarm If the gate hits an object twice while opening or closing, the system will shut down and an alarm will sound for five minutes
- Alternate Outputs With Omni Option board, three push button command control, burglar alarm input and output
- Burglar Alarm With Omni Option board, interfaces with existing home alarm or alarm output
- Digital Motor Protection Entrapment sensor shuts off the motor after it reaches the stall amp for 3 seconds, reverses direction for several inches and stops.
- Electronic Inputs Radio receiver, key switch, hold open loop, center loop, telephone entry system, computer input, fire department key switch, and 3-push-button station
- ERD Sensor If the gate hits a vehicle while closing, it re-opens. If it hits a vehicle wile opening, it stops, reverses 4 to 6 inches, and stops again
- Gate Traveling Time Adjusted by a precision mechanical device and electrical limit switch system
- Integrated Loop Detectors Easy to install, modular, plug in loop detector inputs for exit loop, center loop, and hold open loop
- Intelligent Master/Slave Precise, synchronized movement and communication between two gate operators using three wire RS-485 bi-directional technology
- Magnetic Lock With Omni Option board, magnetic lock system is incorporated, allowing easy addition of the MG1300 locking system to the gate
- Modular Board Uses LEDs to indicate all input and output functions of the gate operator
- Motor Drive Solid state electronic motor drive system is incorporated into the board
- Power Input Controls power input to the board with convenient switch
- Power Management Board includes electronic power management with over current shutdown and automatic recovery
- Soft Stop Gate travels through the cycle at normal speed and comes to a stop slowly for more accurate gate cycle. Equipped with integrated time delay for long mechanical life expectancy
- Spike Suppressors Fast response time (50 nanoseconds) when subject to an impulse surge (lightning strike) up to 100 amps
- Three Push Button Control On board gate operator control for close, stop and open
- Timer Adjustable timer can be set from 0-60 seconds
Elite CSW 200 (Single & M/S) Gate Opener
MECHANICAL SPECIFICATIONS Approval
UL and ETL listed to the latest UL325 and UL991 specifications. Chassis
Constructed with .25 inch sanded, welded, and gold zinc plated sheet metal. Cover
High density polyethylene plastic and stainless steel for excellent heat and corrosion resistance. Cycles
75 cycles per hour with a 600 pound gate. Dimensions
Length = 20.5in x Width = 15in x Height 28in. Emergency Release
The gate is easily disconnected by turning the release handle. the best option is our DC-1000CSW. Finish
All metal parts are gold zinc plated for rust proof protection.
|
