|
Mirror With Flexible Handle
Mirror with flex handle is often used to inspect hard to reach welds. Could be handy for many uses outside welding.
|
|
USD 3.95
ATL Welding Supply-Surplus Distributor
|
|
18
18" Cutting Torch with a 70 degree head. It can be used with Acetylene, LP, Propane, Propylene or Natural Gas. The torch uses Harris style cutting tips. It is pictured with an LP tip.
|
|
USD 65.00
ATL Welding Supply-Surplus Distributor
|
|
46
A 46" long scrap cutting torch with tip. It is designed for use with LP, propane or Propylene gas only. It has a 70 degree head for easily cutting metal on the ground while you stand upright. The torch is being sold with a Harris style 6290NX-2 cutting t ...
|
|
USD 181.50
ATL Welding Supply-Surplus Distributor
|
|
Marquette 20-112 Cutting Torch Attachment
Marquette 20-112 Cutting Torch Attachment is made by Harris Calorific for the Marquette label. It has a 90 degree & will cut with acetylene or fuel gases. The torch comes with an acetylene cutting tip (other tips could be substituted).
|
|
USD 65.00
ATL Welding Supply-Surplus Distributor
|
|
20 Hobart Welding Rod Holders with Dividers
(20) genuine Hobart
|
|
USD 115.00
ATL Welding Supply-Surplus Distributor
|
|
Hobart Welding Rod Holder with Dividers
Hobart Welding Rod Holder with Dividers
|
|
USD 7.50
ATL Welding Supply-Surplus Distributor
|
|
|
|
Genuine Smith SC509 Cutting Torch Head
Genuine Smith SC509 Cutting Torch Head. Includes SC12-4 Cutting Torch Tip. Fits SC Torch Handle.
|
|
USD 100.00
ATL Welding Supply-Surplus Distributor
|
|
Harris 18
The 18 inch Model 142 comes with a 70
|
|
USD 150.00
ATL Welding Supply-Surplus Distributor
|
|
Harris Cutting Torch 880F LP Only
A propane only straight torch that will cut through 6 inches with a head mix system. The stainless steel cutting oxygen lever that has a locking clip for making long cuts without restarting. An in-line tube design gives greater visibility while the protec ...
|
|
USD 110.00
ATL Welding Supply-Surplus Distributor
|
|
Welding Cable Splicer Set
Email this page to a friend
|
|
USD 0.99
ATL Welding Supply-Surplus Distributor
|
|
Century Welding Female Jack Set
Female Jack Set includes two female plugs. Each plug has a 3/8" ID hole for male jacks & 1/2" whole for cable. Female jack sets comes with set screws & plates.
|
|
USD 4.25
ATL Welding Supply-Surplus Distributor
|
|
Victor style Tip End 8-TE
Email this page to a friend
|
|
USD 19.96
ATL Welding Supply-Surplus Distributor
|
|
|
|
Victor style Tip End 6-TE
Email this page to a friend
|
|
USD 13.10
ATL Welding Supply-Surplus Distributor
|
|
Victor style Tip End 5-TE
Email this page to a friend
|
|
USD 14.59
ATL Welding Supply-Surplus Distributor
|
|
Victor style Tip End 3-TE
Email this page to a friend
|
|
USD 8.65
ATL Welding Supply-Surplus Distributor
|
|
Victor style Tip End 1-TE
Email this page to a friend
|
|
USD 12.99
ATL Welding Supply-Surplus Distributor
|
|
Rako Products Control Box 110V 15 A Used
This item is a used Rako Control Box Type MVA 011150. It comes with power cabling as shown in the photo.
|
|
USD 85.00
ATL Welding Supply-Surplus Distributor
|
|
Olympia 1/4 inch Nut Splitting Tool for 12mm Socket
Olympia Nut Splitting Tool. Works with a 12mm socket on nuts up to 1/4" or 6mm in size.
|
|
USD 3.50
ATL Welding Supply-Surplus Distributor
|
|
Crack Check C-NF Weld Inspection Cleaner
Crack Check C-NF Weld Inspection Cleaner
|
|
USD 3.95
ATL Welding Supply-Surplus Distributor
|
|
Weldit Welding Rod Holder Chip Hammer Metal Pick Wire Brush Combo
4pc Welding Accessory Combination Set.
Includes:
Hobart Welding Rods Holder for 14" rods
Spring Handle Chipping Hammer ...
|
|
USD 11.95
ATL Welding Supply-Surplus Distributor
|
|
|
|
